Zenmuse L1

Zenmuse L1

Instant Clarity. Superior Accuracy.

A Lidar + RGB Solution for Aerial Surveying

The Zenmuse L1 integrates a Livox Lidar module, a high-accuracy IMU, and a camera with a 1-inch CMOS on a 3-axis stabilized gimbal. When used with Matrice 300 RTK and DJI Terra, the L1 forms a complete solution that gives you real-time 3D data throughout the day, efficiently capturing the details of complex structures and delivering highly accurate reconstructed models.

Integrates a Lidar module,an RGB camera, and a high-accuracy IMU

Integrates a Lidar module,
an RGB camera, and a high-accuracy IMU

High Efficiency 2 km2 covered in a single flight [1]

High Efficiency
2 km2
covered in a single flight [1]

High AccuracyVertical Accuracy: 5 cm / Horizontal Accuracy: 10 cm [2]

High Accuracy
Vertical Accuracy: 5 cm /
Horizontal Accuracy: 10 cm [2]

Point Rate: 240,000 pts/s

Point Rate: 240,000 pts/s

Supports 3 Returns [3]

Supports 3 Returns [3]

Detection Range: 450 m (80% reflectivity, 0 klx)

Detection Range: 450 m
(80% reflectivity, 0 klx)

IP54 Ingress Protection Level

IP54 Ingress Protection Level

Point Cloud LiveView

Point Cloud LiveView

Digitize without Compromise

Exceptional Efficiency

Generate true-color point cloud models in real-time, or acquire 2 km2 of point cloud data in a single flight [1] using the Livox frame Lidar module with a 70° FOV and a visible light camera with a 1-inch sensor.

Unparalleled Accuracy

Render centimeter-accurate reconstructions thanks to the high-accuracy IMU, a vision sensor for positioning accuracy, and the incorporation of GNSS data.

Ready When You Are

The IP54 rating allows the L1 to be operated in rainy or foggy environments. The Lidar module’s active scanning method enables you to fly at night.

Everything in View

RGB Camera

- 20MP
- 1-inch CMOS
- Mechanical Shutter

Recreate the World in 3D Point Clouds

Point Cloud LiveView

Real-time point clouds provide immediate insights onsite, so operators are informed to make critical decisions quickly.
You can also verify fieldwork quality by checking point cloud data immediately after each flight.

One-stop Post-processing

DJI Terra fuses the IMU and GNSS data for point cloud and visible light calculations, in addition to conducting POS data calculations so you can effortlessly generate reconstructed models and accuracy reports.

Application Scenarios

Topographic Mapping

Quickly generate topographic maps using accurate digital elevation models.

AEC and Surveying

Manage the full project lifecycle using highly accurate point clouds and 3D models.

Emergency Response

Any time of the day, gather critical insights in real-time using true-color point clouds.

Law Enforcement

Gain situational awareness and forensic intel in real-time to make informed decisions on site.

Energy and Infrastructure

Model sparse or complex structures in detail to manage them efficiently and safely.

Agriculture and Forestry Management

Gain insight into vegetation density, area, stock volume, canopy width, and growth trends.

Order Your L1 Today

The L1 is available for order through official DJI Dealers.
Contact us below for the team to reach out.

I agree to the DJI Privacy Policy and the Terms of Use.

[1] Over 30 minutes, at a speed of 13 m/s, a flight altitude of 100 m, with a side overlap rate of 10%, point cloud density > 100 points/m2.

[2] The accuracy was measured after a 5-minute warm up, using Mapping Mission with Calibration Flight enabled in DJI Pilot, and with the RTK in FIX status. The relative altitude was set to 50 m, flight speed to 10 m/s, gimbal pitch to -90°, and each straight segment of the flight route was less than 1000 m. DJI Terra was used for post-processing.

[3] In operations with two or three returns, the point rate is 480,000 pts/s