Specs

Approx. 136 g (including antennas)

76×61×25 mm (L×W×H, excluding antennas and Cold Shoe Adapter)

HDMI: Input/output
USB-C (Top): PD power input/output
USB-C (Bottom): DP input/output, PD power input/output, device activation and firmware updates, log export, phone app connection, and connection to the DJI Ronin series*, Osmo Action 6**, and Osmo Pocket series** devices

The SDI port is available on the DJI SDR Transmission 2 Expansion Plate, which is sold separately.
* Supported models include DJI RS 5, RS 4 Pro, RS 4, RS 3 Pro, Ronin 2, and Master Wheels.
** Supports Osmo Action 6 and Osmo Pocket series (Osmo Pocket 4 and later) via USB-C for monitoring and power supply.

Non-DFS Frequency Band:
2.400-2.4835 GHz
5.150-5.250 GHz
5.725-5.850 GHz
DFS Frequency Band:
5.250-5.350 GHz
5.470-5.725 GHz

The 5.8 GHz and DFS frequency bands are prohibited in certain countries/regions. Check local laws and regulations for more information. 5.600-5.650 GHz is not used.

2.400-2.4835 GHz:
< 20 dBm (SRRC/CE/MIC)

5.150-5.250 GHz:
< 23 dBm (SRRC/CE/MIC)

5.250-5.350 GHz:
< 23 dBm (SRRC/CE/MIC)

5.470-5.725 GHz:
< 26 dBm (CE/MIC)

5.725-5.850 GHz:
< 30 dBm (SRRC)
< 14 dBm (CE)

40 MHz

50 Mbps

The maximum encoding bitrate is 50 Mbps, measured under controlled conditions. Actual encoding and transmission bitrates may vary depending on the environment and transmission distance.

Standby (no external devices connected):
Single Transmitter: Approx. 5.04 W
Single Receiver: Approx. 5.31 W

1T1R Transmission*:
Main Unit: Transmitter approx. 8.52 W, receiver approx. 7.58 W
Each Unit With an Expansion Plate (SDI input/output): Transmitter approx. 10.36 W, receiver approx. 8.89 W

* Measured at a room temperature of 25° C (77° F), at a distance of approximately 10 meters, in a 1T1R setup, using PD for power supply.

USB-C Power Supply Type 1: 15 V, 3 A (PD protocol*)
USB-C Power Supply Type 2: 6.8-17.5 V DC
NP-F Battery Power Supply Voltage: 6.8-8.4 V

* A PD power adapter with an output of 65 W or above is required.

DCI 4K: 23.98/24/25/29.97/30/50/59.94/60fps
4K UHD: 23.98/24/25/29.97/30/50/59.94/60fps
1080p: 23.98/24/25/29.97/30/50/59.94/60fps
1080i (input only on the main unit; input/output on the Expansion Plate): 50/59.94/60fps
720p: 50/59.94/60fps

4K video format is only supported via the HDMI port and the bottom USB-C port of the transceiver main unit.

Input Audio Format: SDI embedded, HDMI embedded, DP embedded
Output Audio Format: 16-bit, 48 kHz, stereo PCM

SDR

35 ms

Camera and screen display latency are not included. Measured when shooting 1080p/60fps and 4K/60fps video.

H.265

4 km (CE)

Measured under CE compliance using one TX and one RX in open, unobstructed, and interference-free controlled conditions.

-10° to 40° C (14° to 104° F)

Approx. 105 g

76×54×25 mm (L×W×H, excluding Cold Shoe Adapter)

HDMI: Input/output
USB-C (Right): Power supply and DJI RS 5 connection
USB-C (Bottom): Power supply, camera control (photo capture and recording start/stop), and connection to DJI Ronin series devices* other than DJI RS 5
SDI: Input/output

* Supported models include DJI RS 4 Pro, RS 4, RS 3 Pro, Ronin 2, and Master Wheels. Please note: When using with Ronin 2 or Master Wheels, the DJI SDR Transmission 2 Gimbal Control Cable (USB-C to 4-pin) is required (sold separately). When using with RS 4 Pro, RS 4, or RS 3 Pro, the DJI SDR Transmission 2 Gimbal Control Cable (USB-C to CAN) is required (sold separately).

USB-C Power Supply Type 1: 15 V/9 V, 3 A (PD protocol*)
USB-C Power Supply Type 2: 6.8-17.5 V DC

* A PD power adapter with an output of 65 W or above is required.

-10° to 40° C (14° to 104° F)

Approx. 91 g

124×110×49 mm (L×W×H)

NATO port
1/4″-20 screw hole × 2
3/8″-16 screw hole
HDMI cable clamp
USB-C cable clamp

-10° to 40° C (14° to 104° F)