FAQ

UPS, short for Uninterruptible Power Supply, is mainly used to supply power to devices through DJI Power 1000 Mini when there is a power outage and prevent accidents that might otherwise be caused.
When electrical devices are connected to the powered-on DJI Power 1000 Mini and both are receiving grid power, press the AC button on the power station and ensure that the AC output indicator shows solid light, then DJI Power 1000 Mini defaults to UPS mode. DJI Power 1000 Mini can start powering the connected devices within 0.01 seconds*. You can decide whether to use this mode based on the device you are using.

^{* Data was tested in a controlled laboratory environment.}

You can update the firmware through DJI Home app.
After connecting DJI Power 1000 Mini to the DJI Home app and configuring the Wi-Fi network, go to Settings > Firmware Update to upgrade to the latest firmware version.

The default warranty period is five years. Certain accessories, including the retractable cable module, are not included in the 5-year warranty coverage. Please refer to the after-sales service policy for full details.

1. DO NOT store the power station for an extended period after fully discharging. Otherwise, the battery may over-discharge and cause irreparable damage to the battery cell.
2. For long-term storage, it is recommended to maintain the product’s battery level at 50% to 70% (ideally around 60%). Storing with high battery level for a long duration can cause the battery to age more quickly, while storing with low battery levels can cause over-discharge. It is recommended to check the battery level every 3 to 4 months during storage and recharge if necessary.
3. Then, recharge and discharge it once roughly every six months: First, discharge the power station to below 15%, power off, and wait for two hours or longer. Then, recharge it to 100% using the Standard Recharge Mode in order to maintain the power station.

If an error code appears on the power station display, you can connect to the DJI Home app to check the specific issue and solution, or visit the DJI Power Series Product Support for more details.

AC power:
Recharging with grid power through the AC input port.

DC power:
1. With a built-in high-power car charging module, you can use the DJI Power Car Battery Charging Cable to connect DJI Power 1000 Mini directly to the fuel car battery for DC recharging.
2. The built-in MPPT module allows you to use the DJI Power MC4 Solar Power Charging Cable to connect DJI Power 1000 Mini to solar panels for efficient DC recharging.
3. Use the DJI Power Car Power Charging Cable to connect DJI Power 1000 Mini to the car’s power outlet for DC recharging.
4. Recharge DJI Power 1000 Mini via the USB-C port or the USB-C retractable cable by connecting the power station to a compatible charger.

AC input power and SDC car charging input power for DJI Power 1000 Mini can be adjusted within the DJI Home app.

After turning on the power, you can press the AC button to enable AC output, or you can enable it remotely in the DJI Home app.
If you press the AC button once, its indicator will blink slowly. AC output will automatically shut down to save electricity if the power station is not charging any device via the AC output ports within half an hour.
If you press and hold the AC button, its indicator will show solid light, and AC output will not automatically shut down.

If the AC input frequency does not match the output frequency currently set on the power station, an error code will be prompted on the power station’s display. In this case, you need to manually switch the AC output frequency:
Ensure AC output is enabled, disconnect the AC charging cable and all connected devices, then press and hold the AC button for approximately 10 seconds until the frequency on the display changes.

The power supply capability will be affected in low-temperature environments, and the output power will decrease.

You can set the auto-off time in the DJI Home app. If there is no continuous output, it will automatically turn off after 30 minutes by default.

The SDC port is capable of the following functions:

Recharging:
1. Use the DJI Power Car Battery Charging Cable via the SDC port to fast recharge DJI Power 1000 Mini from a fuel car battery at up to 400W.
2. Use the DJI Power Car Power Charging Cable via the SDC port to recharge DJI Power 1000 Mini from a 12V or 24V car power outlet at up to 120 W or 240 W, respectively.
3. Use the DJI Power MC4 Solar Power Charging Cable via the SDC port to fast recharge DJI Power 1000 Mini from solar panels at up to 400W.

Power supply:
1. Fast charging intelligent flight batteries of DJI Matrice 4 Series, DJI Mavic 3 Series, DJI Mavic 4 Pro, DJI Air 3 Series, Matrice 30 Series, and DJI Inspire 3 using the corresponding fast charge cable for drones.
2. Supplying power to car-powered appliances via the DJI Power SDC to Car Charger Plug Power Cable.
3. Charging model aircraft batteries outdoors by connecting to the balance charger (model aircraft battery balance charger) via the DJI Power SDC to XT60 Power Cable (12V).

DJI Power 1000 Mini features a built-in MPPT module and fast charging module, but does not support the DJI Power 1kW Super Fast Car Charger or the DJI Power 1.8kW Solar/Car Super Fast Charger, and cannot expand capacity using the DJI Power Expansion Battery 2000.

No, it does not. DJI Power 1000 Mini has a built-in wireless module and can connect directly to Wi-Fi and the DJI Home app.

After the flight, wait until the drone battery has cooled down before connecting it to the corresponding DJI Power SDC fast charging cable; otherwise, charging speed may be affected.
Since the final 5% of charging a drone battery (from 95% to 100%) is completed via trickle charging, the charging speed is relatively slower. You can consider using the battery after it is charged to 95%, as the operating time will not be significantly less than it is when fully charged.

Yes. DJI Power 1000 Mini has a built-in retractable cable module. You can use a tool to pry open the cover from the notch, release the side clips, and then remove and replace the module.

DJI Power 1000 Mini has a built-in bar-shaped LED light. Press once to turn on/off, double-press for SOS, or press and hold to adjust brightness.