Support für Phantom 4 Pro

The P4P uses a 1’’ (CMOS) sensor with 20 million effective pixels, supporting maximum 4K 60p (H.264) and 4K 30p (H.265) video recording with a 100 Mbps maximum video bitrate. The aperture can be adjusted from F/2.8 to F/11. A mode (aperture priority) and S mode (shutter priority) have also been added as camera modes.

The P4P comes with a 16GB SD card. SD cards up to 128GB, Class 10 and UHS-1 rating with writing speed faster than 15MByte/s are compatible. Recommended Micro SD cards are listed below:
1. Sandisk Extreme 32GB UHS-3 V30 MicroSDHC.
2. Sandisk Extreme 64GB UHS-3 V30 MicroSDXC.
3. Panasonic 32GB UHS-3 MicroSDHC.
4. Panasonic 64GB UHS-3 MicroSDXC.
5. Samsung PRO 32GB UHS-1 MicroSDHC.
6. Samsung PRO 64GB UHS-3 MicroSDXC.
7. Samsung PRO 128GB UHS-3 MicroSDXC.

No, the cameras are sized differently. P4P ND filters are available on our online store.

In S-mode, the aircraft can tilt up to 42 degrees while the gimbal can move at most 45 degrees upward and 120 degrees downward. Hence, the gimbal cannot point forward horizontally when the aircraft is flying quickly in S-mode. To solve such issue, move the Pitch of the gimbal downward by at least 12 degrees when flying in S-mode.

100 Mbps.

No, it is made of a magnesium alloy and ceramics.

The camera will use the electronic shutter by default when the shutter speed is higher than 1/2000 or when using the burst shooting function. Otherwise, the mechanical shutter will be used to prevent jelloing.

Windows: VLC, PotPlayer, KMPlayer, MilkPlayer.
IOS: Elmedia Player.

Their remote controllers are different. The P4P+’s remote controller includes a 5.5-inch, 1080p, 1000 nit built-in display. Its screen can be seen clearly in direct sunlight, it can be used in low-temperature environments, and a mobile device is no longer required. The remote controller also features an HDMI port, a micro-SD card slot, and a built-in microphone and a speaker, which allows for live streaming and video editing anytime, anywhere.

The P4P’s remote controller can output HDMI signal with the HDMI Module installed and a mobile device. After installing the HDMI Module, upgrade the remote controller’s firmware to the latest version.
The P4P+‘s remote controller has a built-in HDMI port.

Around three hours.

Users cannot switch between FCC and CE manually. The remote controller will enable FCC or CE mode based on your location in accordance with local laws and regulations.

The remote controller without the display can work for 6 hours when fully charged. The controller with the display can work for 5 hours when fully charged.

Press the C1, C2 and video recording buttons at the same time. After you hear an alarm “D-DD”, press the camera settings dial, and the remote controller will start linking to your P4P.

The P4P is powered by an enhanced version of DJI Lightbridge, and it supports 2.4GHz and 5.8GHz frequency bands.

Yes, but many Wi-Fi and Bluetooth devices also work at the 2.4G frequency band, so interfere is more likely to occur. Currently, the 5.8G frequency band isn’t as widely used, so you’re less likely to encounter interference when using the 5.8G band.

FCC: 7 km, CE: 3.5 km (Unobstructed, free of interference). Actual transmission distance varies depending environmental conditions and operation.

Around 220ms for the remote controller without the display and around 180ms for the one with the display. The actual transmission latency depends on your mobile device’s performance and environmental interference.

720P@30FPS. Actual transmission resolution depends on your mobile device’s performance and environmental interference.

In the DJI GO app, tap Menu and disable “Over Exposure Warning”.

5870mAh, 15.2V, 89.8Wh.

Around 90 minutes.

Keep the Intelligent Flight Battery away from water or moisture. Battery level should between 45% and 65% when the Intelligent Flight Battery is to be stored for a long period of time. If the Intelligent Flight Battery is to be stored for more than three months, it should be fully charged and discharged once every three months to prevent over discharging.

Yes, when the voltage of the battery cells is lower than 3.62V, the display turns yellow.

100W.

The Intelligent Flight Battery will be upgraded when you upgrade the aircraft firmware. When the firmware for the Intelligent Flight Battery needs to upgraded, an Inconsistent Firmware Found warning will display in the DJI GO app. Slide the slider to the right to update the battery firmware.

Battery capacity will decrease significantly when the Intelligent Flight Battery is used at low temperatures (below minus 10 degree Celsius). It is recommended to warm up the Intelligent Flight Battery to 20 degrees Celsius before flight.

The discharge rate of the P4P’s Intelligent Flight Battery is 5C.

When the Intelligent Flight Battery has been stored for a long period of time with over 65% charge, the auto-discharging function will be triggered. The Intelligent Flight Battery will discharge to 65% of the total power automatically while emitting moderate heat.

The DJI charger can charge the Intelligent Flight Battery and remote controller. But it is not recommended to charge the Intelligent Flight Battery and remote controller at the same time.

The subject to be tracked needs to be placed in the middle of the screen for identification. If “GO” is shown on the screen after you drag a box around the subject, the subject has been identified. You can start tracking after tapping “GO”. The tracked subject should not be similar in color or patterning to its surrounding environment. You can track optimally when your P4P flies at a height between three meters to five meters and five meters to 15 meters from the tracked subject.
The P4P can also use the new Spotlight and Profile functions in ActiveTrack Mode.

You can fly your P4P in any direction within -25 degrees to + 25 degrees controllable range of the gimbal in TapFly Mode. You can set the speed in TapFly between 1 m/s to 13 m/s in the DJI GO app. When encountering an obstacle, the P4P will ascend to avoid it. When “Enable Horizontal Obstacle Avoidance” is enabled, the P4P will generate a route automatically to avoid the obstacles from both sides. If it cannot avoid an obstacle, the P4P will hover in place.
TapFly for the P4P can be used in forward mode, backward mode and free mode.

No. In P-mode, only the P4P's front and rear vision systems are enabled. In Beginner Mode and tripod mode, the P4P's left and right infrared sensors are enabled.

0.2 meters to 7 meters.

14 m/s.

The DJI GO app can run on both iOS and Android mobile devices. For more details, please see the user manual.

14 m/s, the same as the max speed in P mode.